Steel & Wood Laboratory Furniture Installation Guidance: Step-by-Step Instructions for a Seamless Setup

MAX LAB’ s laboratory furniture is engineered for durability, function, and safety, but proper installation is key to ensuring long-term performance. Please read the following instructions carefully before beginning the setup.

What’s Included in Your Shipment

Before you begin, please inspect your delivery and ensure you have received all components:

Steel Frame Structures (legs, support beams, crossbars)

Work Surfaces (phenolic resin, epoxy resin, stainless steel, or wood)

Cabinet Modules (wood or steel drawers and storage units)

Fasteners (screws, bolts, washers, anchors)

Installation Tools (Allen keys, L-wrenches – depending on your order)

Assembly Drawings and Product Labels (match these to your packing list)

Optional Add-ons: sink modules, reagent racks, fume hood frames, etc.

Required Tools (Not Included)

To complete installation, please prepare the following:

Electric drill/screwdriver with bits

Adjustable wrench

Bubble level

Tape measure

Protective gloves

Rubber mallet

Pencil or marker for alignment

Pre-Installation Preparation

Review Layout Plan:
Refer to the provided room layout or CAD drawings. This will help ensure each bench and module is installed in the correct location.

Check Floor Condition:
Make sure the installation surface is level, clean, and free of debris. Concrete or tiled flooring is preferred for heavy-duty lab furniture.

Unpack Components Carefully:
Remove all packaging with care. Do not use sharp blades near finished surfaces to avoid scratches or damage.

Organize Components by Station:
Group the parts for each workstation together. This simplifies the workflow and prevents mix-ups.

Step-by-Step Installation Guide

1. Frame Assembly (Steel Structure)

a. Layout the Leg Assemblies
Position the leg frames in accordance with your layout drawing. Legs should be evenly spaced to support the worktop, typically 900–1200mm apart.

b. Connect Horizontal Beams and Bracing
Using provided bolts and washers, attach horizontal support beams between legs. Crossbars add lateral stability—install them as shown in the assembly drawings.

c. Check Level and Alignment
Use the bubble level to ensure all legs and frames are perfectly vertical and level before tightening bolts.

2. Install Cabinet Bases (Optional)

If your bench includes under-counter storage cabinets:

Place the cabinets between leg structures.

Cabinets are typically freestanding but can be fastened to frame or floor for added security.

Make sure drawers and doors open freely without obstruction.

3. Install Work Surface

Depending on your chosen material:

a. Resin or Wood Tops:

Position the top surface on the frame or cabinets.

Align flush with the front edge for ergonomic access.

Secure from below using screws or adhesive brackets (as specified).

b. Stainless Steel Tops:

Lay the surface gently onto the frame.

Fasten with stainless steel bolts or clips to avoid corrosion.

IMPORTANT: Do not overtighten screws. Overcompression can crack resin or deform the frame.

4. Accessory Installation

a. Reagent Racks

Mount vertical posts to the rear edge of the workbench.

Attach shelving at desired heights using provided clamps or brackets.

b. Sink Units (if applicable)

Drop-in sinks should be sealed using chemical-resistant silicone.

Connect plumbing lines (water and drain) using qualified technicians.

c. Power Strips & Fixtures

Mount electrical strips to underside or rear of workbench.

Ensure proper grounding and follow local electrical codes.

5. Final Adjustments & Inspection

Confirm all screws, bolts, and attachments are secure.

Adjust levelers on legs or cabinet bases if required.

Clean all surfaces with a damp cloth to remove dust or fingerprints.

Inspect for scratches or damage; contact our service team if needed.

Safety Tips

Always wear protective gloves during assembly.

Never exceed the recommended weight capacity for benches or racks.

Ensure sinks and power modules are installed by certified professionals.

Keep the area clear of obstructions during assembly to avoid tripping hazards.

Maintenance Recommendations

Wipe down surfaces regularly with a mild detergent.

Avoid using strong acids or solvents unless worktops are chemical-resistant.

Check fasteners every 6 months to ensure structural integrity.

Lubricate drawer slides and hinges annually to maintain smooth operation.

Need Help?

If you encounter any issues during installation, or you want to buy a new lab furniture, we’re here to assist. Contact our technical support team:

Email: ada@maxlabfurniture.com

Phone：+86 132 4232 3168

Tel: +86 020 3881 3639

Whats App: +86 132 4232 3168